Round-Front Floor-Mount Two-Piece Toilet, Standard Projection
Model ST-0425HS is a floor-mounted two-piece toilet in glossy white vitreous china, 28.7 × 16.5 × 31.1 in (730 × 418 × 790 mm) — a standard project-grade model for distributors, builders and hospitality buyers. cUPC-ready, available factory-direct OEM/ODM and private label. Browse all two-piece toilets or request a quote.
Send a spec. Get a real quote in 12h.
Engineer-reviewed. cUPC · CE · ISO 9001 ready. 30–45 day lead time, FOB or CIF.
12 consecutive years at KBIS and IBS.
Standard on every shipment.
ST-0425HS Standard
A round-front two-piece at standard projection
ST-0425HS is a floor-mounted two-piece toilet measuring 28.7 by 16.5 by 31.1 inches. It is the standard-projection unit in the two-piece range.
28.7 in. projection
The published size gives 28.7 inches front to back and 16.5 inches across. Specify it where the plan has the floor space for a standard-projection pan.
31.1 in. overall height
Overall height is published as 31.1 inches. Check that figure against a window sill, a niche or a shelf before the unit is specified.
The compact unit and other options are listed in the two-piece toilet collection.
Fit & Clearance
28.7 in. projection and 31.1 in. height
Both the depth and the height need checking against the room.
The 28.7 inch projection has to clear the door swing with room to stand. The 16.5 inch width sets the gap to a vanity or side wall.
Overall height matters where anything is fixed above the unit. At 31.1 inches published height, a low shelf can leave too little clearance to service the cistern.
Confirm clear height above the unit against the published 31.1 inch dimension before the layout is fixed.
Construction & Finish
Glazed china body, floor mounted
Two fields describe the surface of ST-0425HS: vitreous china ceramic, glossy white.
Vitreous china, glossy white
Material and finish are taken directly from the specification for ST-0425HS. No other finish is listed for this model.
The unit is floor mounted and supplied as two pieces. Handling, storage and site sequencing differ from a wall-hung installation.
Store tanks and bowls on their original packing until the room is ready to receive them.
Compliance
Documentation and test reports on request
Documentation and any test data are confirmed for this model code before the order is placed.
No certification, flush volume or water efficiency figure is published for ST-0425HS on this page, and none is claimed.
Import requirements for sanitaryware vary by country. Give the destination market in the RFQ so the quotation can set out what documentation can be provided.
Procurement
Ordering ST-0425HS in volume
Ceramic codes such as ST-0425HS carry a published 30 piece minimum.
Buyers taking both the standard and compact units should quote them as separate lines, since each code carries its own minimum. Packing and pallet marking to your own brand are arranged through the SANIKB OEM and ODM program.
Include these details with the RFQ
- Model ST-0425HS and quantity
- Whether the compact model is also required
- Destination port and delivery terms
- Seat and fittings in scope or excluded
- Flush and water data for the market
- Pallet and packing arrangement
- Rough-in drawing for the submittal
- Required arrival date
Quote each ceramic code separately. Minimums are counted per model, not per shipment.
FAQs
What is the ST-0425HS two-piece toilet and how is it built?+
What are the dimensions and rough-in for the ST-0425HS?+
Why choose a two-piece toilet like the ST-0425HS for projects?+
What flush configuration does the ST-0425HS use?+
What are the MOQ, OEM/ODM and wholesale terms for the ST-0425HS?+
Is the ST-0425HS cUPC-ready and how is it packed for export?+
This Standard Floor-Mount Two-Piece Toilet is cast in high-fired vitreous china ceramic with a fully glazed, glossy white finish for a hard, non-porous surface that wipes clean and resists staining. The two-piece format ships the tank and bowl as separate pieces that join on site with a tank-to-bowl gasket and bolts, which simplifies handling, replacement, and crate packing. At a full-size 28.7 x 16.5 x 31.1 in (730 x 418 x 790 mm), it suits standard-height residential and hospitality bathrooms. For the smaller-footprint version of the same line, compare the compact two-piece model, or browse the wider one-piece toilet collection to weigh seamless single-unit alternatives. SANIKB controls casting, glazing, and quality control in-house for consistent batch quality.
The unit is floor-mounted and sets over the closet flange with a standard wax or foam seal and closet bolts; the tank then bolts to the bowl with the supplied gasket. It uses a standard 12 in (305 mm) rough-in so installers match common North American waste outlets, and the separable design means the tank or internal fittings can be serviced without removing the whole fixture. Always confirm the exact rough-in and clearances against the spec drawing before committing an order. Buyers standardizing toilets across a property can pair this standard-height unit with seamless single-unit models from the one-piece toilet collection in one shipment to suit different room sizes.
SANIKB supplies this two-piece toilet factory-direct as the manufacturer, supporting OEM, ODM, and private-label programs with your logo and branding on the product and packaging, custom cartons and documentation, and configured flush volume to suit your market water-consumption rules. The vitreous china body is cUPC-ready for North American specification, with exact certificate scope confirmed per model and market. The unit ships in foam-cushioned export crate packaging engineered for ocean freight, at a minimum order quantity of 30 pcs, and third-party pre-shipment inspection is welcome. Distributors, importers, dealers, and project buyers deal with the plant directly rather than a trading layer; request a quote with target volumes, branding, and destination port.
How we work
From enquiry to shipment
A factory-direct process built for importers, distributors and project buyers. No trading layer in between.
-
01
Send the enquiry
Tell us the model, quantity, destination market and any branding or packaging requirement. A spec sheet or drawing helps but is not required to start.
-
02
Our sales team contacts you
A named account manager follows up by email or WhatsApp, confirms the specification and clarifies anything missing before pricing.
-
03
Quotation
You receive a written quotation with unit price, MOQ, packing details, lead time and the trade term you asked for. Entry, mid and premium build levels can be quoted side by side.
-
04
Sample approval
We send a sample for finish, function and packaging sign-off. Branded samples are produced once artwork is confirmed.
-
05
Production and shipment
Mass production starts after sample approval and deposit. QC and inspection run before loading, then the order ships to the agreed port.
OEM and ODM to your specification
We develop to a brief. Send a reference model, a drawing or simply the price band and market you are targeting, and we will propose what fits. Entry, mid and premium builds are all available from the same factory.
- Your logo on product, carton and documentation
- Private-label packaging and manuals
- Custom finish matched to your standard
- Custom dimensions and tooling where volume supports it
- Product development from your reference or price target
- Destination-market documentation prepared on request