Walk In Tub Dimensions: Will It Fit a 60-Inch Alcove?
Eight of 13 SANIKB walk-in tub sizes are 52 in long; seated models stand 35.9–47.2 in overall, so height decides fit before width.
On this page
Quick answer: Eight of the 13 SANIKB walk-in tub size variants are 52 in long, and seated shells run 25.2–31.7 in front to back. Seated walk-in models stand 35.9–47.2 in overall, while the low lie-down format stands 21.1–21.5 in. Against a 60 x 30 alcove, 9 of 13 size variants fit the shell envelope; against a 60 x 32 alcove, 12 of 13 fit. Among the 8 seated 52 in variants, width spans 25.2–31.7 in, but overall height spans 36.0–47.2 in.
Most walk in tub dimensions fit a standard 60 in alcove on paper. Eight of the 13 SANIKB walk-in tub size variants are 52 in long, and seated shells run 25.2–31.7 in front to back. The figure that changes most is overall height, so check it before you check anything else.
Seated walk-in models stand 35.9–47.2 in overall, while the low lie-down format stands 21.1–21.5 in. That gap decides whether a bathtub clears a window sill, a niche or a low ceiling. Length and width decide whether the shell fits the opening at all.
This guide uses our 12 live walk-in tub pages and their 13 size variants as the data set. You get a full size table, fit counts for 60 x 30 and 60 x 32 alcoves, a measuring checklist and the format trade-offs. Every size below is the overall envelope from the product page: length x front-to-back width x overall height. On several drawings that height runs to the top of the deck fittings or grab bar, and the shell rim sits lower. The guide also covers the space requirements around the bathtub, which decide fit as often as the shell does.
Walk in tub sizes: all 13 size variants compared
Start with the full list, because the formats differ more than the names suggest. Walk in tub dimensions on a quote should always read length x front-to-back width x overall height, in that order. The table lists each model with its stored inch and metric size, its format and its jet system. The two right-hand columns compare the shell envelope with a 60 x 30 and a 60 x 32 alcove.
| Model | Size (L x W x overall H) | Format | Jet system | 60 x 30 alcove | 60 x 32 alcove |
|---|---|---|---|---|---|
| BG329 | 49" × 26.0" × 37.8" (1250 × 660 × 960 mm) | Compact seated, glass door | Soaking Only | Envelope fits | Envelope fits |
| BG-306 | 52" × 25.2" × 37.9" (1320 × 640 × 962 mm) | Narrow seated | Whirlpool | Envelope fits | Envelope fits |
| BG-321 | 52" × 29.7" × 36.0" (1320 × 755 × 915 mm) | Seated, inward door | Whirlpool + Air | Envelope fits | Envelope fits |
| BG327 | 52" × 29.5" × 47.2" (1320 × 750 × 1200 mm) | Tall seated, tapered door | Whirlpool + Air | Envelope fits | Envelope fits |
| BG-311 | 52" × 31.7" × 36.2" (1325 × 805 × 920 mm) | Seated, U-shaped door | Whirlpool + Air | Too wide | Envelope fits |
| BG-316 | 52" × 27.6" × 36.2" (1325 × 700 × 920 mm) | Seated, sloped seat back | Whirlpool + Air | Envelope fits | Envelope fits |
| BG-310 | 52" × 29.5" × 38.5" (1325 × 750 × 979 mm) | Seated, U-shaped door | Whirlpool | Envelope fits | Envelope fits |
| BG-304 | 52" × 30.3" × 41.3" (1325 × 770 × 1050 mm) | Seated, inward door | Whirlpool | Too wide | Envelope fits |
| BG-312 | 52" × 28.3" × 40.9" (1330 × 720 × 1040 mm) | Seated, headrest | Whirlpool + Air | Envelope fits | Envelope fits |
| BG-305 | 55" × 29.3" × 35.9" (1395 × 745 × 911 mm) | Stepped seat | Whirlpool | Envelope fits | Envelope fits |
| BG-308A | 60" × 31.7" × 39.2" (1520 × 805 × 995 mm) | Double-ended, center door | Whirlpool | Too wide | Envelope fits |
| B8080-6030 | 60" × 30.0" × 21.1" (1524 × 762 × 535 mm) | Low lie-down, no seat | Whirlpool | Envelope fits | Envelope fits |
| B8080-7232 | 72" × 31.9" × 21.5" (1830 × 810 × 545 mm) | Low lie-down, no seat | Whirlpool | Too long | Too long |
Use the overall height for window, niche and doorway clearance. Take the rim height from the approved drawing, because several drawings dimension the rim separately and lower.
Read the table in this order. First rule out bathtubs that are too long or too wide for the space. Then compare heights against the bathroom wall above the bath. Then pick a jet system and a door layout.
Eleven of the 12 pages are sold as L and R handed versions of one size. B8080 is the exception: it is sold by size (B8080-6030, B8080-7232) with no L or R suffix. Its door, drain and pump end come from the approved drawing for each size. All 12 pages are white acrylic shells, so color is not a sizing variable here.
Will a walk-in tub fit a 60 x 30 or 60 x 32 alcove tub space?
The standard alcove tub space in US housing is a three-wall opening about 60 in long, with the bathtub apron facing the bathroom. Hotels and apartments often build it at 60 x 30 or 60 x 32. Our guide to 60 x 30 and 60 x 32 alcove bathtub sizes covers the standard tubs that usually fill those openings.
A walk-in tub is not a drop in bathtub. It stands on the bathroom floor with its apron and door facing out, so the alcove walls frame three sides. That is why length and front-to-back depth are the first two checks.
Against a 60 x 30 alcove, 9 of 13 size variants fit the shell envelope; against a 60 x 32 alcove, 12 of 13 fit. The comparison uses length up to 1524 mm (60 in) and width up to 762 mm (30 in) or 813 mm (32 in).
Which models miss a 60 x 30 opening
Four size variants fall outside a 60 x 30 alcove. BG-304 is 30.3 in wide, and BG-311 and BG-308A are 31.7 in wide. B8080-7232 is 72 in long and misses both openings.
So in a 30 in deep alcove, your seated options are BG-305, BG-306, BG-310, BG-312, BG-316, BG-321, BG327 and BG329. B8080-6030 is the low lie-down choice at 60 x 30. In a 32 in deep alcove, you add BG-304, BG-311 and BG-308A.
What "fits" means in this count
Fit here compares the shell envelope only. It does not prove the bathtub will install cleanly. The pages publish no flange, apron-extension or rough-in figures. Treat every fit result as a shortlist, and confirm it against the approved drawing for the SKU you order. In a 32 in deep alcove, BG-311 and BG-308A at 31.7 in leave almost no margin, so measure the finished opening before you count them in.
A 52 in shell in a 60 in alcove: plan the leftover length
Most seated walk-in bathtubs are shorter than the alcove bath they replace. A 1320 mm shell in a 1524 mm opening leaves open length at one end. That gap needs filler or extension panels, or new framing, before the bathroom walls are tiled. Tile, plumbing and installation details all depend on which end you leave open.
Decide which end gets the gap before you order. The pump end needs service access, and the door end needs clear floor in front of it.
Then ask three questions at quotation. Does the shell need a wall flange or a tile flange? Which panels or trims are included, and which do you source locally? Where is the drain on the approved drawing?
Two formats reduce the filler problem. BG-308A is 1520 mm long, close to a full 60 in opening. B8080-6030 is 1524 mm long, the full nominal 60 in, so it leaves little or no gap, but also no tolerance. Measure the finished opening at the floor and at rim height, and confirm the flange detail on the drawing before you count on a no-filler install. For a 55 in opening, the stepped-seat Walk-In Whirlpool Tub with Stepped Seat and Grab Bars, 55 in is the closest match.
Walk in tub height: the number that changes most
Length and width cluster tightly across this range. Height does not. Among the 8 seated 52 in variants, width spans 25.2–31.7 in, but overall height spans 36.0–47.2 in.
A tall bath can hit a window sill, a recessed niche, a shelf or a sloped ceiling. It can also change where the hand shower and grab bars sit on the wall.
Tall seated models
The tallest is the Tall Walk-In Whirlpool and Air Tub with Tapered Glass Door, 52 in. BG327 rises to 1200 mm (47.2 in). Next come BG-304 at 1050 mm (41.3 in) and BG-312 at 1040 mm (40.9 in). BG327 is made for seated bathing, and its height costs the most wall space above the rim.
Before you specify one of these, measure from the finished floor to the first obstruction above the tub on the back wall. Check the window sill, the bottom of any shower niche and any soffit. If that measurement is close to the bathtub height, choose a lower model.
Lower seated models (overall height)
Overall height, including fittings, is 35.9–36.2 in for BG-305, BG-321, BG-311 and BG-316. It is 37.8–38.5 in for BG329, BG-306 and BG-310. Rim heights on the drawings are lower; the BG-306 drawing below dimensions its rim separately from the 962 mm overall figure. Request the rim figure on the approved drawing when wall space above the rim matters.
The lower models leave more bathroom wall above the tub for a shower rail or bars. That helps when an existing window or niche must stay. For how water depth relates to rim height, see how to measure bathtub soaking depth.
Narrow walk in tub and small walk in tub options for tight spaces
Tight spaces are either short or shallow front to back. Pick the model that solves your constraint.
The narrowest shell is the Narrow Walk-In Whirlpool Tub with Grab Bars, 25.2 in Wide, 52 in. BG-306 measures 1320 × 640 × 962 mm (52 × 25.2 × 37.9 in). It suits shallow alcoves and small bathrooms where bathroom floor in front of the tub is limited.
BG-306 keeps three grab bars on a narrow deck. A tall inverted-U bar stands beside the door, a horizontal bar runs along the back deck, and a U handle sits on the front deck. Confirm that wall and deck space suit those positions in your bathroom.
The shortest shell is the Compact Walk-In Soaking Tub with Seat and Black Fittings, 49 in. BG329 measures 1250 × 660 × 960 mm (49 × 26.0 × 37.8 in). It is the only variant under 1320 mm long, and it is soaking only.
A compact shell solves short rooms, but it leaves more open length in a 60 in alcove. Use it where the bathroom itself is short, not to save money in a full-length opening. BG329 is soaking only, so there is no jet pump to reach through an access panel.
Double ended walk in tub: center door, two seats
A double ended walk in tub puts the door in the middle of the front apron. The Double-Ended Walk-In Whirlpool Tub with Center Door, 60 in follows that layout. BG-308A measures 1520 × 805 × 995 mm (60 × 31.7 × 39.2 in).
Features differ from the seated range: each end has its own seat and headrest. A center spout and a hand shower sit on the deck. A U grab bar is mounted on the front deck just left of the door.
Use this format when the full 60 in length should be used by the shell, not filler. Check two things first. The 31.7 in width leaves almost no margin in a 32 in deep alcove, so measure the finished opening and confirm the flange on the drawing. The center door needs clear floor in the middle of the room side. BG-308A is made in L and R versions, so confirm on the approved drawing what each one changes.
Lay down walk in tub: the low 60 and 72 in format
A lay down walk in tub works differently from a seated bathtub. The Low Lie-Down Walk-In Whirlpool Tub with Glass Door, 60 & 72 in stands at ordinary bath height and has no seat. The bather enters through a glass door in the front apron and reclines against a sloped backrest.
Two sizes are made. B8080-6030 is 1524 x 762 x 535 mm (60 x 30.0 x 21.1 in). B8080-7232 is 1830 x 810 x 545 mm (72 x 31.9 x 21.5 in).
The 60 x 30 size matches a standard alcove footprint by envelope, with little or no gap and no tolerance. Confirm the flange and the finished opening before you plan a no-filler install. It also keeps the wall above the bath clear for a shower, like a standard bathtub. The 72 in size needs a longer opening than a standard alcove tub. Large tubs like B8080-7232 also need a longer delivery path, so measure the route as well as the space.
The deck is wide, flat and left clear of taps. The faucet mount is floor or wall, so the filler is specified separately. Plan that supply location in the wall or floor before framing. B8080 is sold by size with no L or R version, so take the door position, drain location and pump end from the approved drawing for each size.
Door side, handing and swing: match them to the plumbing wall
Eleven of the 12 models come in L and R handed versions (B8080 is sold by size only). On most pages the hand decides which end holds the taps and door; BG-304's page says it changes the door side. BG-308A's page leaves the change to the approved drawing. Match the version to the existing drain and supply wall using that drawing, or plan to move the plumbing.
Stand in the bathroom facing the alcove. Note the drain location and which side the bathroom door is on. Then pick the version whose drain end, per the approved drawing, matches the existing drain.
Door swing is the next check. Only two pages state an inward-opening door. The Walk-In Whirlpool Tub with Inward-Opening Glass Door, 52 in (BG-304) is hinged at the tap end. The Walk-In Whirlpool and Air Tub with Inward Door and Back Jets, 52 in (BG-321) has an inward-swinging U-shaped glass door.
On every other model, the swing direction is confirmed on the approved drawing or at quotation. Do not assume it. A door that swings out needs clear floor in front of the tub, and a toilet or vanity can block it.
Two layouts need extra care. BG327 has a tapered door, wider at the top than at the bottom. BG-308A has a center door. Both change where the bather stands while stepping in.
Order lines: SKUs by hand and size
Quote each handed version as its own line. Several pages ask for documents per SKU, so name the L and R quantities separately. The table lists the SKUs as each page states them.
| Model | SKUs | What the versions change, per page |
|---|---|---|
| BG-304 | BG-304L, BG-304R | Door side; same size |
| BG-305 | BG-305L, BG-305R | One size, two hands |
| BG-306 | BG-306L, BG-306R | One size, two hands |
| BG-308A | BG-308AL, BG-308AR | Confirm on the approved drawing what each one changes |
| BG-310 | BG-310L, BG-310R | One size, two hands |
| BG-311 | BG-311L, BG-311R | One size, two hands |
| BG-312 | BG-312L, BG-312R | L and R layouts on the approved drawing |
| BG-316 | BG-316L, BG-316R | One size, two hands |
| BG-321 | BG-321L, BG-321R | One size, two hands |
| BG327 | BG327L, BG327R | Drawing shown for one hand; swing and layout on the approved drawing |
| BG329 | BG329L, BG329R | Left-hand and right-hand versions of one size |
| B8080 | B8080-6030, B8080-7232 | Sold by size; no L or R suffix |
For a project with mirrored bathrooms, count the rooms by drain end before you split the quantity between L and R. For B8080, split the quantity by size instead. Ask for the approved drawing of every SKU on the order, not one drawing for the model.
Measure-before-you-order checklist
Walk in tub dimensions only help if you compare them with real site numbers. Take these measurements on site, in this order, before you request a quote. Write each one on the floor plan you send with the request.
- Alcove length, wall to wall. Measure at the floor and at rim height, because walls are not always plumb.
- Front-to-back depth. Compare it with the shell width in the table. 30 in and 32 in openings give different shortlists.
- Height to the first obstruction. Measure to the window sill, niche or soffit. Compare it with the overall height, such as BG327 at 1200 mm or BG-304 at 1050 mm.
- Drain location. Note which end it is at, and match it to the L or R version on the approved drawing.
- Door swing clearance. Measure clear floor in front of the tub and note any toilet, vanity or bathroom door nearby.
- Floor level. Check the bathroom floor for slope. BG-321 stands on leveling feet and BG-312 on small feet; ask how other models are leveled.
- Service access. Confirm you can open a panel at the pump end after tile is installed.
- Delivery path. Measure every doorway, hall turn and stair on the route.
If a low threshold height, seat height or door opening width matters for your users, request it on the drawing. For accessible rooms in covered US facilities, check the 2010 ADA Standards (U.S. Access Board), section 607 Bathtubs for clear floor space, grab bars, seats and controls.
Delivery path, doorways and service access
A walk-in bathtub arrives as one rigid shell, usually with the door in place; confirm the packing at quotation. It cannot fold or flex through a tight turn. The smallest doorway on the route is often the real limit.
Compare the bathtub's width and height with each doorway on the route. The shell may need to pass on its side, so both dimensions count. A tall model like BG327 has less room to turn in a narrow hall than BG-321 at 36.0 in.
Plan service access at the same time. Jetted models have a pump that may need service after installation. Leave a removable panel at the pump end, and do not tile over it.
The pump's electrical requirements are not on the pages. Request them for your destination market at quotation. Follow the installation manual and local code for the supply.
Air tub vs whirlpool vs soaking only: what each system adds
The air tub vs whirlpool question changes bathroom planning more than bathtub size. By page, 6 are whirlpool, 5 are whirlpool plus air, and 1 is soaking only.
| System | Models | What the pages show |
|---|---|---|
| Whirlpool | B8080, BG-304, BG-305, BG-306, BG-308A, BG-310 | Whirlpool jets; positions vary (BG-304 has floor, seat-back and side jets; B8080 has wall jets) |
| Whirlpool + Air | BG-311, BG-312, BG-316, BG-321, BG327 | Two large jets and small air holes on BG-312, BG-316, BG-321 and BG327; round deck buttons |
| Soaking Only | BG329 | No jets; seat, glass door and deck valves |
Count the hydrotherapy jets on the approved drawing rather than from photos. BG-321 adds three cylindrical back jets at the seat and three deck buttons. BG-316 sets slot jets around the seat and four deck buttons. BG327 and BG-311 also show four round deck buttons.
Jetted tubs of other types, without a door, are in the whirlpool tubs collection. If you want only a seated soak with no pump, BG329 removes the electrical and access planning entirely.
Walk in tub pros and cons, framed on space and planning
The side door removes the need to step over a full tub wall; ask for the threshold height on the drawing. A walk-in tub holds more water than a standard bath and the bather waits inside while it fills and drains. Check water heater capacity and hot water supply against the fill volume on the spec sheet you request.
How to choose walk-in tub dimensions by project type
The right bathtub size depends on who uses the bathroom and what the building already has. Walk in tub dimensions narrow the list; the users and the existing plumbing pick the model. These rules match the formats to common project types.
Senior living and assisted living
Start with the lower seated models at 35.9–36.2 in overall, such as BG-321, BG-311 or BG-316. They leave more wall above the rim for grab bars and a hand shower. Use the narrow BG-306 where bathrooms are shallow, and check section 607 if the room is a covered accessible room.
Hotel and multifamily standard rooms
Repeat one model across every matching bathroom type to simplify spare parts and filler details. Measure your standard bathroom layout once, then confirm the shortlist against it. For a full 60 x 30 opening, B8080-6030 leaves little or no gap, but confirm the flange and finished opening first. For 60 x 32, BG-308A uses most of the length. A walk-in tub is not automatically a section 607 accessible bathtub. Where a room counts toward required accessible units, confirm the tub, bar positions and controls with the authority having jurisdiction before you specify it.
Accessibility remodels and distributors
Remodels usually inherit an existing drain, so pick the L or R version whose drain end, per the approved drawing, matches it, or budget to move the drain. Choose by height first, because existing windows and niches rarely move. Distributors covering both opening sizes can stock BG-305, BG-306, BG-310, BG-312, BG-316, BG-321, BG327, BG329 and B8080-6030, which fit both by envelope. List overall heights clearly on every quote.
For certification, the product pages list cUPC certification. Ask for the certificate and its validity date with your quote. Do not treat it as an accessibility rating. cUPC covers plumbing; for jetted models, ask separately which electrical listing covers the pump and controls for your market.
Ready to price a bathroom type? Send the model, size and quantity you need, plus your alcove length, depth and height. Compare all formats in the walk-in tubs collection, including the widest 52 in seated shell, the Walk-In Whirlpool and Air Jet Tub with 4 Deck Buttons, 52 in. SANIKB replies in writing within 12 business hours, and minimum order, samples and lead time are confirmed in the written quotation per model.
Frequently asked questions
Will a walk-in tub fit in a standard 60-inch alcove?
Most walk-in tubs fit a 60-inch alcove by envelope, but fit depends on depth and the approved drawing. Against a 60 x 30 alcove, 9 of 13 SANIKB size variants fit the shell envelope; against 60 x 32, 12 of 13 fit. A 52 in shell leaves open length that needs filler panels or framing. Shortlist by envelope, then confirm flange and drain details on the drawing.
How tall is a walk-in tub?
Walk-in tub overall height runs 35.9–47.2 in for seated SANIKB models and 21.1–21.5 in for the low lie-down B8080. The tallest is BG327 at 1200 mm (47.2 in), followed by BG-304 at 1050 mm (41.3 in). Measure from the finished floor to any window sill, niche or soffit above the tub. Choose a lower model if that clearance is tight, and take rim height from the approved drawing.
Do walk-in tub doors open inward or outward?
Door swing varies by model, so check the approved drawing for each SKU. Among our 12 walk-in tub pages, only BG-304 and BG-321 state an inward-opening door. Every other model has its swing confirmed on the drawing or at quotation. An outward door needs clear floor in front of the tub, so measure that space before you choose.
What is the difference between an air tub and a whirlpool tub?
Whirlpool tubs push water through jets, while air tubs push air through small holes in the shell. Among our walk-in pages, 6 are whirlpool, 5 combine whirlpool and air, and BG329 is soaking only. Jetted models need a pump supply and an access panel. Request the pump's electrical requirements for your market at quotation before you finalize the room.
— Rokan, SANIKB