S-Curve Rim Slipper Tub on Plinth Base, Waisted Oval, 65 in
Wholesale · 20 ft / 40 ft · Mix available · Below 1 container: your own China forwarder required.
SANIKB D-8055 is a gloss white acrylic slipper tub on a plinth base, with a thin rim that is raised over one end and steps down in an S-curve near mid-length to a lower line. The flared body pinches in to a narrow vertical band at the floor, and the plan is waisted, with rounded ends and inward-curving long sides. It is made as D-8055 at 1650 × 730 × 600 mm (65 × 28.7 × 23.6 in), with a center drain. The rim has no tap holes; D-8055 takes a floor-standing or wall-mounted filler. SANIKB quotes within 12 business hours.
Compare it with other raised-end models in the slipper tub collection.
More in Slipper Tubs
MOQ per model · one 40HQ container, quantity set by tub size
Tub sheet
Size and installation of D-8055
Send a spec. Get a real quote in 1 business day.
Engineer-reviewed. CE · ISO 9001 ready. 30–45 day lead time, FOB or CIF.
We send quotes within 1 business day after receiving the necessary product, quantity and destination details.
12 editions of the International Builders' Show (IBS).
Factory documentation
Certification scope depends on the selected model and destination market. Request model-specific documents with your quotation.
Rim & Base
An S-curve step in the rim
The rim of D-8055 runs high over one end, drops in an S-curve near mid-length and continues at a lower level to the other end.
Two rim levels joined by one curve
The raised half forms the backrest and the lower half runs to the far end. The step between them is a single S-shaped curve rather than a straight slope.
Flared body on a narrow band
The body flares out toward the rim and pinches in to a vertical band at the floor, a plinth base that stands on a smaller footprint than the rim outline.
Freestanding plans from oval to rectangular are compared in the freestanding bathtub range.
Size & Drain
1650 × 730 mm with a center drain
D-8055 measures 65 by 28.7 by 23.6 inches (1650 by 730 by 600 mm), with the 600 mm taken at the raised half of the rim.
- D-8055
- 65" × 28.7" × 23.6" (1650 × 730 × 600 mm)
- Drain
- Center
- Inner Depth
- 460 and 470 mm (18.1 and 18.5 in)
- Base
- Plinth band
The drain is central on the drawing, so the waste sits at the middle of the footprint whichever way the raised end faces. The plan is waisted, but the rim still needs its full 730 mm (28.7 in) in the layout.
Mark the center waste on site from the approved D-8055 drawing.
Material & Finish
Gloss white acrylic over a plinth band
D-8055 is made from pure acrylic sheet in gloss white and finished with a thin rim.
White
Gloss along the step
The gloss finish follows the rim as it steps from the high end to the low end. Use the approved sample as the finish reference for the whole order.
The thin rim at the step and the narrow plinth band are the exposed points in handling. Ask how both are supported in the carton.
Check the rim step and the plinth band for damage on arrival.
Compliance
Compliance documents for D-8055
D-8055 documents are issued against D-8055, the one size made.
Compliance documents for D-8055 are matched to your destination market. Ask for the current document details against D-8055 for a submittal.
Say where the tubs are going when you enquire, and you will get an answer within 12 business hours.
Procurement
Ordering D-8055
One 1650 mm size of D-8055 is produced; allow 30-45 days after sample approval.
- SKU
- D-8055
- Standard Lead Time
- 30-45 days after sample approval
Send the room plan with the enquiry if the raised half of the rim should face a particular wall, so the orientation can be agreed before the sample.
Include these details with the RFQ
- Quantity of D-8055
- Floor or wall filler choice
- Center waste fitting
- Destination market and port
- Private-label marking
- Delivery window
Note on the enquiry which wall the raised half should face.
How we work
From enquiry to shipment
A factory-direct process built for importers, distributors and project buyers. No trading layer in between.
-
01
Send the enquiry
Tell us the model, quantity, destination market and any branding or packaging requirement. A spec sheet or drawing helps but is not required to start.
-
02
Our sales team contacts you
A named account manager follows up by email or WhatsApp, confirms the specification and clarifies anything missing before pricing.
-
03
Quotation
You receive a written quotation with unit price, MOQ, packing details, lead time and the trade term you asked for. Entry, mid and premium build levels can be quoted side by side.
-
04
Sample approval
We send a sample for finish, function and packaging sign-off. Branded samples are produced once artwork is confirmed.
-
05
Production and shipment
Mass production starts after sample approval and deposit. QC and inspection run before loading, then the order ships to the agreed port.
OEM and ODM to your specification
We develop to a brief. Send a reference model, a drawing or simply the price band and market you are targeting, and we will propose what fits. Entry, mid and premium builds are all available from the same factory.
- Your logo on product, carton and documentation
- Private-label packaging and manuals
- Custom finish matched to your standard
- Custom dimensions and tooling where volume supports it
- Product development from your reference or price target
- Destination-market documentation prepared on request