Edge Crush Test: What ECT Says About a Sink Carton
Read ECT as a corrugated-board result, then check the finished carton and loaded fixture package separately before approving a packaging specification.
On this page
An edge crush test measures the edgewise compression resistance of corrugated board. It does not establish a sink carton's permitted contents weight or prove that the packaged sink will arrive undamaged. For a purchasing or packaging specification, read the ECT result alongside the carton drawing, construction and evidence for the complete fixture package.
A 32 ECT or 44 ECT designation is useful when checking the specified board. It leaves other questions open: which carton was made from it, how the sink is restrained, what accessories are included, and which distribution conditions the package was evaluated against. Keep those questions separate when comparing quotations or approving a replacement box.
What an ECT result tells you
ECT is a material test on a board specimen rather than a shipment test. ZwickRoell's explanation of edge crush testing distinguishes the board result from a box compression test on the whole box. Record the test method and edition with the result; the abbreviation alone does not identify the specimen preparation or testing conditions.
Start by checking whether the report actually belongs to the proposed carton material. A supplier's general board data sheet, a report for another production lot and a test of the proposed board are different evidence. Ask for the sample identification and its relationship to the carton specification, then keep both documents under the same packaging revision.
32 ECT vs 44 ECT: compare the specified board
The numbers identify different nominal edge-compression ratings, commonly expressed in pounds per linear inch. A 44 ECT designation specifies a higher edgewise criterion than 32 ECT. It does not, by itself, establish a better finished package for every sink or an allowable stacking height.
When considering a change from 32 to 44 ECT, ask what else changes. The carton supplier should identify whether the quoted construction, dimensions, closure and inserts remain the same. Comparing only the printed number can hide a different wall construction or an altered packing arrangement.
Comparison item |
What to obtain |
Decision it supports |
|---|---|---|
Board designation |
Specified ECT grade and the associated report or material record |
Whether the proposed board meets the agreed material criterion |
Carton design |
Drawing, dimensions, wall construction and revision |
Whether two quotations describe the same outer carton |
Internal packing |
Insert layout, restraints and accessory locations |
Whether the sink is packed in the same configuration |
Package evaluation |
Report identifying the carton and the tested fixture configuration |
Whether the evidence addresses the proposed package |
For example, a proposal may quote 44 ECT while its supporting package report covers an earlier carton revision. The next action is to reconcile the revision and test configuration, rather than approve the substitution from the higher number alone. The same check applies when a supplier offers a lower grade as an equivalent replacement.
32 ECT vs 200 lb test: the numbers use different units
These labels describe different board properties. Westpak's laboratory explanation reports ECT in lb/in and Mullen burst results in pounds per square inch, or psi. In a 200-lb burst-test designation, the number refers to a 200 psi bursting criterion; it is not permission to put 200 pounds of contents in the box.
The two ratings therefore are not interchangeable measurements or direct contents-weight limits. A quotation that changes from an ECT designation to a burst designation needs an explicit agreed board specification and suitable package evidence. A larger-looking number is not a comparison of like units.
Ask the carton supplier to spell out which property is specified, the test method used and the reported units. If a purchasing system has only one field called “box strength,” add the property name to that entry. This prevents a later order from treating a burst rating as though it were an ECT requirement.
ECT, box compression and transport evidence answer different questions
FEFCO's test-method listings separate board tests from tests on corrugated packaging, including compression and handling-related methods. Select the evidence for the question being asked rather than treating every report labelled “packaging test” as equivalent.
Evidence |
Question to ask |
Information still needed |
|---|---|---|
Board ECT report |
What edge-compression result was recorded for this material? |
Its relationship to the proposed carton |
Box compression test |
What result was recorded for this whole box? |
Box configuration, conditioning and whether contents or inserts were included |
Loaded-package evaluation |
What happened to the fixture and packaging in the documented test? |
Exact packed model, procedure, acceptance criteria and intended distribution route |
A box compression report should state how the box was assembled and tested. Do not assume that a reference to BCT means a loaded sink carton was tested. Likewise, a board report does not document drops, vibration or damage to the fixture. An engineering estimate of compression performance should be identified as an estimate and kept separate from measured results.
Record corrugated box flute types without prescribing a universal choice
The flute designation belongs in the construction record, together with the wall arrangement, board thickness and material specification. A flute letter alone is not a complete sink-carton design. Obtain the supplier's actual construction details instead of applying a generic “this flute is best for heavy sinks” rule.
Ask for a cross-section or construction description that matches the quotation. Check whether “double wall,” a flute combination and the reported caliper all describe the same proposed board. Keep this information with the carton drawing so a replacement order can be checked against the approved design.
Separate outer-box changes from internal-packing changes. Replacing a cradle, moving a drain assembly or adding an accessory carton may change the packed configuration even when the outer board designation is unchanged. Identify the revised arrangement before deciding whether earlier evidence still covers the shipment.
A practical sink-carton approval record
Use one record to connect the fixture, carton and supporting reports. For stainless products, the manufacturing and QC guide provides related product-documentation context. For larger fireclay models, the 36-inch sink planning guide connects packaging questions with model selection.
Identify the exact sink SKU, accessories included and packed mass from the current packing record.
Record the outer-carton drawing, dimensions, board construction, material criterion and closure instructions.
Attach the insert layout and packing sequence, including where loose components are restrained.
Link each report to its sample, packaging revision, test conditions and evaluation criteria.
Document the intended parcel, pallet or other distribution route and the handling instructions approved for it.
Name who approved the configuration and which changes require another review.
Receiving teams can then check the delivered packaging against an identifiable specification. Photograph visible damage and the carton markings before separating the fixture from its packing. Keep the model and shipment reference with those photos; a crushed corner and a board-grade label describe different parts of the investigation.
Frequently asked questions
Can ECT tell me how many sink cartons to stack?
Not on its own. Obtain the documented stacking and handling instructions for the actual packed configuration. A board value leaves the carton design, contents, arrangement and storage conditions unresolved.
Is 44 ECT automatically necessary for a fireclay sink?
The material designation is only one part of the packaging specification. Request the approved carton and packing arrangement for the selected model, with evidence that matches that configuration. Sink material alone does not establish one universal ECT requirement.
Can I reuse a previous report after changing the carton supplier?
Have the responsible packaging reviewer compare the proposed material, design and packing configuration with those identified in the report. Record the basis for accepting the change or requesting further evaluation. Supplier name alone does not establish equivalence.
What should I request when the quotation says only “strong export carton”?
Request the carton drawing and construction, the specified board property and units, the packing layout and the relevant evaluation records. These details create a repeatable purchasing specification and make later substitutions easier to review.