Bathroom TV Planning: How Hotels Specify a Mirror with Television

A bathroom tv sounds simple on a hotel brief: one mirror, one screen, one happy guest. In practice the unit joins glass, lighting, a display and electrical connections in a single wall element. SANIKB offers two round LED TV mirrors, KS-5001 and KS-5002, each 500 × 500 mm with a rear halo and a screen area in the lower portion. This guide shows how hotel and multifamily teams specify that kind of product without guessing.

You will get a decision table, a review sequence for picture, controls and power, and a list of documents to request. The goal is a sample you can approve in writing, then repeat across every room.

Bathroom TV decision table: what to settle first

Start with the models on the table below. It lists the two TV mirrors and the round LED mirrors that sit beside them in the range. Every figure comes from the catalog entry for that model.

The table answers only the geometry question. It does not tell you the screen size, the inputs or the power arrangement of the TV mirrors. Those items are confirmed per model in the written quotation, and the rest of this article shows how to ask for them.

What do the two SANIKB TV mirrors include?

The TV mirror collection holds two products. KS-5001 and KS-5002 are both round, both 500 × 500 mm, and both use a rear halo for the lighting effect. The screen area sits in the lower portion of the mirror face.

That layout matters for room planning. The upper part of the circle stays a reflective surface, while the lower part carries the picture. Guests see themselves and the screen in one glance, but not in the same spot. You should decide early which of those two jobs matters more in your room type.

SANIKB does not publish a screen diagonal, input list, waterproof or IP rating, or power rating for the TV mirrors, so each is confirmed per model. Do not write any of those values into a bid document. Request written confirmation from the factory before you fix a purchase description. The LED mirror range, including the TV mirrors, is ETL certified at range level.

Here is one of the companion round mirrors in the range, which shows how a clean circular outline looks on a wall:

Why a bathroom mirror with television is not a normal vanity mirror

A standard vanity mirror has one job. A bathroom mirror with television has at least three: reflect, light the face and show a picture. Each job pulls the design in a different direction, and your specification has to say which one wins when they conflict.

Reflection first, screen second

Most guests use a bathroom mirror for grooming. They stand close, they want even light, and they look at themselves. A screen asks for a different posture, often farther back or seated on the edge of a tub. If the mirror is the main tool in the room, treat the screen as an extra. If the screen is the feature, accept that part of the glass is given over to it.

Write that priority into the room brief. A short line such as "grooming first, entertainment second" helps designers, installers and the hotel operator agree on what a good result looks like.

Why a TV in bath zones needs a separate review

A television near a tub or shower brings moisture, steam and splash into the picture. A plain dry-room display plan does not cover that. The SANIKB catalog does not document a waterproof or IP rating for the TV mirrors, so do not assume one.

Ask the factory how the exact model handles moisture, and request that answer in writing. Keep the screen well away from direct spray in your layout until you hold that confirmation. This one question prevents more rework than any other item on the list.

Hotels often manage this risk by zoning. Place the screen where the guest sits or stands to watch, and keep the splash path from taps and shower heads away from it. Your designer can mark that zone on the plan once the factory confirms how the model handles moisture.

How do you separate mirror geometry from screen geometry?

Treat the mirror and the screen as two shapes on one wall. The catalog gives you the mirror outline for KS-5001 and KS-5002: round, 500 × 500 mm. It does not give you the visible screen area, so that second shape has to come from the factory.

Put both outlines on the room elevation. Mark where the mirror center sits against the vanity, where the lower screen area falls, and where the guest stands. Keep these fields apart in your documents:

• Overall mirror size and outline, as listed for the model.
• Visible screen area and its position inside the mirror, confirmed in writing.
• Mounting interface and any service space, confirmed against the model spec sheet.
• Connection locations for power and signal, confirmed per model.

Do not read a slim edge as proof of a shallow wall recess. Overall depth for the TV mirrors is not in the catalog, so request it before anyone cuts a cavity. For the round LED mirrors in the same range, the catalog lists a depth of 35 mm on the KS-010 models, and that figure belongs only to those models.

Two more habits keep the elevation honest. First, label the screen area on the plan with the words "confirmed by factory" until the number arrives, so nobody treats a guess as a dimension. Second, show the vanity, the faucet and the light switch on the same sheet, because a round mirror at 500 × 500 mm is small enough that a small misplacement changes how it reads over a basin.

Think about eye level too. A round unit has no flat bottom edge to align with a splashback or a shelf, so installers need a clear reference line. Agree the center height with the designer before any fixing, and keep the hotel's own seated-guest and standing-guest positions in view.

What must the hotel TV system do?

Before you pick a display, ask your AV or IT team what the room needs. The right answer depends on the hotel system, not on the mirror. Write the answers down so the supplier can respond to each point.

Typical questions include the signal source, the control method and the audio path. Does the property use a set-top box, an antenna feed or a network service? Does the guest use a remote, a wall control or a phone? Will sound come from the screen or from a separate speaker?

The words "TV mirror" do not establish a smart platform, streaming apps, casting or compatibility with a hotel control system. Treat each of those as a separate request. Ask for it in writing, and test it on the exact unit you plan to buy. Leave any unconfirmed function out of the purchase description.

A simple way to run this review is a four-column sheet. In the first column list the function. In the second, write what the hotel needs. In the third, record what the factory confirms. In the fourth, record what you saw during the sample test. Gaps between columns two and three are your open items.

How do you judge picture visibility in the room?

A screen behind mirror glass behaves differently from a bare panel. Room light, window light and the mirror's own LEDs all change what the guest sees. A demo video in a dim showroom is not the same test as a vanity opposite a bright window.

Check the sample in the conditions of your real rooms. Look at it in daylight, under the vanity fixtures and with the mirror lighting in each state. Then view it from standing and seated positions. Include content with dark scenes, bright scenes, menus and small text.

Also check the mirror with the television off. In a hotel bathroom the glass spends most of its time as a plain mirror, so the off state is the state guests see most. Look for visible edges, uneven reflection or a screen area you can see through the glass when it should look like a mirror.

Test more than one time of day if the room has a window, because afternoon sun and evening lamps give very different results. Record the room-light conditions with your result. A note that says "approved under warm vanity light, curtains open" lets the next reviewer reproduce your test and compare it fairly.

What does the guest control sequence look like?

Run the unit the way a guest would. Switch it on, choose the intended source, change the volume, mute and return to standby. Then cut room power and restore it in the order your hotel expects. Note what comes back on its own and what needs another action.

If the system depends on an external box, test the display and that box together in their installed positions. Check that the remote or control method reaches the equipment once the mirror is on the wall. Do not hide a device behind fixed finishes before you know how it communicates and how it will be serviced.

Mirror lighting adds one more layer. Round LED mirrors in this range offer touch, sensor and Bluetooth options, for example on the Framed Backlit Bathroom Mirror in the KS-010-1004 series. For the TV mirrors, ask which controls are independent and which settings persist after a power cut. Put that behavior in the approved configuration record rather than relying on a general "smart" label.

How do you coordinate power, signal and heat?

Ask for the supply information, the connection points and the power arrangement for the complete assembly. The project's qualified electrical and AV teams should plan the installation from the current product instructions. For the United States, bathroom electrical work follows the NFPA 70 National Electrical Code and the local adoption of it, including ground-fault protection requirements for bathrooms.

Ask the factory for the environmental and heat-management needs of the exact model. Confirm any required openings or ventilation space, and confirm that connections stay reachable after installation. Do not borrow clearances or limits from another brand's manual, because the numbers belong to that product.

Where you plan a recessed install, request the mounting method for that specific model. Coordinate the cavity, the support, the wall finish and the access path on one elevation. Overall mirror size alone does not tell you how deep a cavity must be or how a unit is lifted out for service.

Service access is a hotel question as much as an installer question. Decide who replaces a failed part, how long a room can be out of use, and whether the unit can be removed without damaging the wall. Ask the supplier to describe the removal procedure in writing.

How do you write the TV mirror into a bid schedule?

A bid schedule line should leave no room for a second reading. For each TV mirror, list the model code, the listed size, the lighting arrangement and the quantity. Add a line that says screen details, inputs, power and moisture guidance are confirmed per model in the written quotation.

Keep the mirror lines and the system lines separate. The mirror belongs to the supply package. The set-top box, network access, remote and any external speaker usually belong to the AV package. When both sit in one line, nobody is responsible for the interface between them, and that interface is where room-ready dates slip.

Add an acceptance clause that points to the approved sample. For example, state that delivered units must match the signed sample record for lighting behavior, picture check and control sequence. This turns a vague promise into something your receiving team can test with a phone and a checklist.

If your project mixes TV mirrors with plain round mirrors, give them clearly different schedule codes and mark the rooms on the plan. A mixed-up delivery is easy to prevent on paper and expensive to fix once the wall is finished.

Which round mirrors work beside a TV mirror?

Many hotels do not put a screen in every bathroom. A common plan is to use the TV mirror in selected suites and a matching round mirror elsewhere. The round LED mirrors collection gives you that second group, and the wider LED mirror catalog covers other shapes.

Same-shape companions

Four mirrors in the KS-010 series share a round shape and the same five diameters, from 600 mm to 1000 mm, at 35 mm depth. The Black Frame Round Ring LED Bathroom Mirror shows a perimeter band with a rear halo, while the Black Round LED Mirror uses a slim black perimeter. The gold-border KS-010-1004 adds a gold-colored edge for a warmer look.

Lighting-control options

The KS-010 models list seven configuration options: Single Touch, Double Touch, Triple Touch, Infrared Sensor, Bluetooth, Radar Sensor and Aromatherapy Spray. They list two color temperatures, 6500 K and 3000 K. Pick one control scheme per project so housekeeping and guests see the same behavior in every room.

If you want color effects, the Round RGB Halo LED Mirror in the RGBC series has a white perimeter band and an RGB rear halo in three sizes. For a lighter frame, the White Mirror with Lights in the CW series comes in three sizes with a pale perimeter. Match companions to the TV mirror by sight, using a physical sample.

How do you choose by project type?

The right plan changes with the building. A boutique hotel, a multifamily tower and a distributor stocking for contractors all use the same mirror differently.

Hotels and hospitality fit-outs

Hotels care most about repeatability. Approve one sample room, record the lighting, controls and picture result, and require every delivered unit to match it. Decide which room types get the TV mirror, and keep that list short and clear in the schedule. Involve the hotel's AV team before ordering, not after delivery.

Operations matter too. Ask who handles guest complaints, who resets the unit, and how housekeeping cleans a mirror with a screen area. Write cleaning guidance into the handover pack, using the care information the factory supplies.

Multifamily and distributor projects

Multifamily developers usually want a clean, lower-complexity bathroom. A TV mirror can serve as a premium upgrade in model units or top-tier apartments, with a standard round mirror in the rest. Keep the power and signal rough-in planned for every unit that might receive the upgrade, so an option does not need wall repairs later.

Distributors and contractors should confirm what each quotation line contains. List the model, the size, the configuration options and the quantity. Because the TV mirrors are only two models, a clear product schedule keeps ordering simple and avoids mixing a TV unit with a plain round mirror by mistake.

What are the common mistakes when you specify a bathroom TV?

Most failures come from assumptions rather than defects. Watch for these patterns in your own project:

• Treating the 500 × 500 mm outline as the screen size. The screen is a separate dimension that the catalog does not state.
• Assuming a waterproof or IP rating because the product sits in a bathroom.
• Writing "smart" into the bid without naming the exact functions.
• Approving the picture in a dim showroom and never testing it near the real window.
• Cutting wall cavities before the factory confirms the mounting method.
• Skipping the power-restore test, then finding the screen stays off after an outage.
• Mixing models in the schedule so a plain round mirror lands where a TV mirror was planned.

Each mistake has the same fix. Put the question in writing, get the answer in writing and test the sample against it. That habit also protects you when the order scales from a pilot floor to a full property.

Which documents should you request before approving a sample?

Ask for a short, model-specific set of papers and compare them against the sample you hold. Request the following from the factory for KS-5001 or KS-5002, whichever you plan to buy:

• The model spec sheet with visible screen area and overall dimensions.
• Mounting and installation instructions for your wall type.
• Power and connection information for the complete assembly.
• Signal and control information, including any remote or control interface.
• Moisture and environmental guidance for use near a tub or shower.
• Service and replacement instructions for the display and electrical parts.
• Cleaning and care instructions for the mirror face.

Where an item is missing, request written confirmation from the factory instead of filling the gap yourself. Confirm each answer against the model spec sheet. If two papers disagree, ask which one is current before you accept either.

Treat this list as a gate, not a courtesy. If the factory cannot supply an item for the exact model, record that gap in your project file and decide whether to proceed, wait or switch to a plain round mirror for that room type. Having the choice written down protects your schedule and your budget.

Keep these papers with your approved sample record. When a later delivery arrives, compare it against the same file. That single comparison catches most mismatches before installation starts.

How should you plan samples, quantities and approval records?

Minimum order quantity, sample terms and lead time are confirmed in the written quotation for each model. SANIKB replies within 12 business hours, so you can settle these points before your schedule depends on them.

Plan the sample stage as a short test, not a formality. Order one unit, mount it in a mock-up or a real room, and run the full review: geometry, picture, controls, power restore and cleaning. Record each result with a photo and a note on the room conditions.

Then write the approved configuration as one page. It should name the model, the size string, the control option, the lighting settings and the confirmed screen details. Attach the factory's written answers. Procurement, the installer and the hotel operator can all work from that page.

For a larger order, repeat a lighter version of the check on arrival. Open one carton per model, compare it with the approved page and confirm the model code matches your schedule. If anything differs, flag it before installers touch the wall.

Finally, set a decision date for each open item. A written question with no deadline tends to sit in an inbox. If screen size, moisture guidance and power details are still unanswered when the sample is due, move the sample date rather than approve on faith. A short delay costs far less than a corrected wall.

Request a quote for your bathroom TV project

Send us the model, the size and the quantity you need, plus the room types and the signal system your hotel uses. We will confirm screen details, power, moisture guidance, minimum order, samples and lead time per model in the written quotation. Browse the TV mirrors collection, pick KS-5001 or KS-5002, and request your quote with the details above. A short project note on the bathroom tv layout speeds up the reply.

Frequently asked questions

Is a TV mirror suitable for a wet bathroom?

Moisture suitability depends on the exact model and is confirmed per model, because SANIKB does not publish a waterproof or IP rating for the TV mirrors. Request written confirmation from the factory before you place a screen near a tub or shower. Until you hold it, keep the unit out of direct spray in your layout.

How big are SANIKB's TV mirrors?

KS-5001 and KS-5002 are both round TV mirrors listed at 500 × 500 mm, with a rear halo and a screen area in the lower portion. The visible screen size is not published, so confirm it against the model spec sheet. Use the mirror outline for wall planning and the screen figure for picture planning.

Is SANIKB's LED mirror range certified?

SANIKB's LED mirror range is ETL certified at range level, and that covers the TV mirrors as part of the range. Certification does not state screen features, inputs or moisture ratings. Treat those as separate items, request them in writing for the model you plan to buy, and keep the answers with your approval record.

What should I send to get a quote?

Your quote request needs the model, the size and the quantity, plus the room types and the signal system your hotel uses. Minimum order quantity, samples and lead time are confirmed in the written quotation per model. SANIKB replies within 12 business hours, so you can compare options and decide on a sample order quickly.

— Rokan, SANIKB