Bidet Plumbing for Standalone Bidets: Supply, Drain and Spacing
A standalone bidet needs hot and cold supplies, its own trap and UPC spacing: 15 in to a side wall, 30 in center to center. SANIKB bodies are 345–365 mm wide.
En esta página
Quick answer: SANIKB lists 13 ceramic standalone bidet bodies, 6 wall-hung and 7 floor-standing back-to-wall, and all 13 are 345–365 mm wide. The 2021 UPC sets a bidet at least 15 in (381 mm) from its center to a side wall, 30 in (762 mm) center to center from a similar fixture, with 24 in (610 mm) clear in front. The SANIKB bidet drawings show a Ø35 tap hole on six bodies and Ø40 on LJ-DE03, LJ-DE06 and LJ-DE08, read from the drawings. All 4 SANIKB bidet faucets are deck-mounted, single-hole faucets listed as cUPC.
Bidet plumbing for a standalone bidet comes down to three checks. You need a hot and a cold water supply with shut-off valves, a small waste line with its own trap, and enough floor and wall room beside the toilet. Get those three right before the wall is closed, and the bidet installation itself is a simple job later.
This guide is for contractors, designers and developers adding a separate ceramic bidet next to the toilet. It covers the code spacing, the supply and drain checklist, and the wall-hung versus back-to-wall choice. It uses SANIKB bidet products as the data set: 13 ceramic bodies and 4 faucets, with every size taken from the product records. This is about the standalone bidet fixture only, not bidet seats, attachments or smart toilets.
What bidet plumbing a standalone bidet needs
A standalone bidet is a low ceramic basin with its own faucet and waste. It is plumbed more like a bathroom sink than a toilet. There is no toilet tank, no flush and no large toilet bowl waste. Warm water comes in through a deck mounted faucet, sprays into the bowl for cleansing, and leaves through a waste at the bottom.
Plan for these items at every bidet position:
- Two water lines. One hot water line and one cold water line, each ending in its own shut off valve.
- A waste with a trap. A lavatory-size waste and trap, run to the drain line and vent like any other bathroom fixture.
- Backflow protection on the supply. The code treats the bidet supply as a cross-connection risk.
- A hot water limit. The code caps the temperature of the warm water leaving the bidet.
- Fixing support. Blocking for a back-to-wall body, or an in-wall frame or carrier for a wall hung bidet.
- Clearance. Side, center-to-center and front clearance per the plumbing code.
Treat every generic figure in this bidet plumbing guide as typical. Confirm it on the model spec sheet and with your local code before rough-in.
Wall-hung or back-to-wall: the decision table
Every SANIKB bidet body falls into one of two mounting types. Six are wall-hung and seven are floor-standing back-to-wall. Both types fix to the wall at the back, so the difference is what carries the weight. Pick the mounting first, because it decides the framing, the waste route and which toilet the bidet should match.
| Check | Wall-hung bidet | Back-to-wall bidet |
|---|---|---|
| SANIKB bodies | 6 (FT-276, FT-277, LJ-DA12, LJ-DA15, LJ-D09WH, LJ-D03WH) | 7 (LJ-DE09, LJ-DE03, LJ-DE08, LJ-DE06, LJ-DB15, LJ-D03, LJ-D09) |
| Length (projection) | 520–565 mm (20.5–22.2 in) | 485–560 mm (19.1–22.0 in) |
| Width | 355–365 mm | 345–365 mm |
| Height | 310–340 mm (12.2–13.4 in) | 315–405 mm (12.4–15.9 in) |
| What carries the load | In-wall frame or carrier, or rated blocking | The floor; the back fixes to the wall |
| Waste route | Usually into the wall; confirm on the model drawing | Confirm on the model drawing |
| Best match | A wall-hung toilet on the same wall | A back-to-wall or floor-standing toilet |
| Floor cleaning | Open floor to clean under the bidet | Clean around the ceramic foot |
SANIKB lists 13 ceramic standalone bidet bodies, 6 wall-hung and 7 floor-standing back-to-wall, and all 13 are 345–365 mm wide. That narrow width band means mounting, not width, is the real design choice.
Bidet dimensions: all 13 SANIKB bodies
Here is every SANIKB bidet body, sorted by mounting type and then by length. Sizes are length × width × height, exactly as listed for each model. Use this table to check bidet size against your bathroom plan before you request drawings.
| Model | Mounting | Size (L × W × H) | Finishes |
|---|---|---|---|
| LJ-DE09 | Floor-standing, back-to-wall | 485 × 365 × 325 mm | White |
| LJ-DE03 | Floor-standing, back-to-wall | 500 × 345 × 315 mm | White |
| LJ-DE08 | Floor-standing, back-to-wall | 505 × 360 × 320 mm | White / Matt Black |
| LJ-DE06 | Floor-standing, back-to-wall | 530 × 365 × 370 mm | White |
| LJ-DB15 | Floor-standing, back-to-wall | 535 × 365 × 400 mm | White |
| LJ-D03 | Floor-standing, back-to-wall | 560 × 360 × 400 mm | White / Matt Black |
| LJ-D09 | Floor-standing, back-to-wall | 560 × 360 × 405 mm | White / Matt Black |
| FT-276 | Wall-hung | 520 × 360 × 310 mm | White / Black |
| FT-277 | Wall-hung | 520 × 360 × 310 mm | White / Glossy Black |
| LJ-DA12 | Wall-hung | 530 × 365 × 310 mm | White |
| LJ-DA15 | Wall-hung | 530 × 365 × 310 mm | White |
| LJ-D09WH | Wall-hung | 550 × 360 × 325 mm | White / Matt Black |
| LJ-D03WH | Wall-hung | 565 × 355 × 340 mm | White / Matt Black |
The shortest bidet is the 485 mm back-to-wall bidet LJ-DE09, at 485 × 365 × 325 mm (19.1 × 14.4 × 12.8 in). The longest is the 565 mm wall-hung bidet LJ-D03WH, at 565 × 355 × 340 mm (22.2 × 14.0 × 13.4 in). For a tight wall-hung position, the FT-276 wall-hung bidet in White or Black is 520 × 360 × 310 mm (20.5 × 14.2 × 12.2 in).
Mounting for LJ-D09WH, LJ-DA15, LJ-DB15, LJ-DE03, LJ-DE06, LJ-DE08 and LJ-DE09 is confirmed on the drawing issued with the quotation.
Width is fixed, projection is the variable
Across all 13 bodies, width moves by only 20 mm. Length moves by 80 mm, from 485 mm to 565 mm. So when a bidet does not fit, the problem is almost always projection from the wall, not width.
That changes how you measure a bathroom:
- Measure from the finished wall. Projection is counted from the tile face, not the stud. Thick tile or a furred-out wall eats into the front clearance.
- Add the front clearance to the length. The UPC wants 24 in (610 mm) of clearance in front of the bidet (the IPC 21 in). Add that to the bidet length to get the depth the position needs.
- Do not shop by width. A 345 mm body and a 365 mm body need the same side spacing, because the code measures from the centerline.
- Swap length, not mounting, when you are short. A short back-to-wall bidet like LJ-DE09 frees up projection.
The three shortest bodies (LJ-DE09 485 mm, LJ-DE03 500 mm, LJ-DE08 505 mm) need written factory confirmation of the mounting. At 315–325 mm tall, they also sit about 80 mm lower than LJ-D03 and LJ-D09.
Switching mounting: the LJ-D03 and LJ-D09 pairs
Two model codes, LJ-D03/LJ-D03WH and LJ-D09/LJ-D09WH, are listed in both mounting types; confirm with the factory that each pair shares the same bowl design before you mix them in one project. The pairs show what switching the mounting changes. The answer is height, by a wide margin, while length barely moves.
| Design | Back-to-wall | Wall-hung | Change |
|---|---|---|---|
| LJ-D03 | LJ-D03: 560 × 360 × 400 mm | LJ-D03WH: 565 × 355 × 340 mm | Length +5 mm, height -60 mm |
| LJ-D09 | LJ-D09: 560 × 360 × 405 mm | LJ-D09WH: 550 × 360 × 325 mm | Length -10 mm, height -80 mm |
A back-to-wall body reaches the floor, so its height includes the foot. A wall-hung body is only the ceramic basin. Its finished rim height is set by where you install the fixing points on the wall.
What this means for planning:
- Projection stays the same. Both pairs stay within 10 mm on length, so the front clearance plan does not change.
- Rim height becomes an installer decision. With the 550 mm wall-hung bidet LJ-D09WH, give the plumber who will install it a target rim height that matches the toilet next to it.
- Framing changes completely. The LJ-D03 back-to-wall bidet at 560 × 360 × 400 mm stands on the floor. Its wall-hung twin needs a frame or carrier in the wall.
- Finish stays the same. All four bodies come in White and Matt Black.
Bidet clearance: the UPC 402.5 spacing rules
Bidet clearance is set by the plumbing code, not by the bidet. The 2021 Uniform Plumbing Code (IAPMO) treats a bidet the same way as a water closet in section 402.5. Check your local code, since your jurisdiction may adopt a different edition or a different code.
Centerline to side wall: 15 in
No bidet may be set closer than 15 in (381 mm) from its center to a side wall or obstruction. Measure from the bidet centerline to the finished wall. A vanity, a shower curb or a tall cabinet counts as an obstruction.
Center to center: 30 in
A bidet may not be closer than 30 in (762 mm) center to center to a similar fixture. In UPC jurisdictions, confirm with your inspector that a toilet counts as a similar fixture.
Clear space in front: 24 in
The UPC requires at least 24 in (610 mm) of clear space in front of a bidet. That space is measured from the front of the bidet. A swinging door, a vanity edge or a shower door must stay out of it.
The 2021 UPC sets a bidet at least 15 in (381 mm) from its center to a side wall, 30 in (762 mm) center to center from a similar fixture, with 24 in (610 mm) clear in front. Since every SANIKB body is narrow, these code numbers will govern your layout long before the ceramic does.
In IPC jurisdictions, the 2021 International Plumbing Code (ICC) names the bidet directly in section 405.3.1. It sets 15 in (381 mm) to a side wall, 30 in (762 mm) center to center to an adjacent fixture such as the toilet, and 21 in (533 mm) clear in front.
Planning a bidet next to toilet on one wall
The most common layout puts the bidet next to toilet on the same wall. That lets you install the supplies and the waste in one wall cavity. Here is the planning math for a wall between two side walls, using the 30 in rule between the two fixtures.
- Toilet centerline: 15 in from the first side wall.
- Bidet centerline: 30 in from the toilet centerline.
- Second side wall: 15 in from the bidet centerline.
- Total wall length: 15 + 30 + 15 = 60 in, before any other fixture.
Then check the depth. The deeper of the toilet and the bidet, plus the front clearance (24 in under the UPC, 21 in under the IPC), sets the bathroom depth. A long toilet can control this number, so check its projection too.
Match the mounting of the pair for a consistent look. A wall-hung bidet can be set to any rim height on its frame, so set it to the toilet beside it. Pair a wall-hung bidet with one of the wall-hung toilets, and a back-to-wall bidet with a back-to-wall toilet.
Bidet hot and cold water: the supply checklist
A standalone bidet needs both a hot and a cold water supply. The faucet mixes them into warm water for a comfortable wash.
Here is the typical bidet plumbing supply setup. Confirm sizes and fittings on the faucet spec sheet and with your local code.
- Two stub-outs. Separate hot and cold supplies, each ending in its own shut off valve below the bowl or in the wall.
- Angle stops. A 3/8 in compression angle stop on each line is typical. Confirm on the model spec sheet and local code.
- Flexible connectors. A water supply hose runs from each stop to the faucet tails. Leave each hose enough slack for service, and fit a new hose rather than an old one.
- Access. Keep both stops where a plumber can reach them with the bidet installed.
Under section 410.2 of the 2021 UPC, the bidet water supply must be protected by an air gap or an approved backflow method. Ask the faucet supplier what backflow method the faucet and its fittings use, and confirm it with your inspector.
Section 410.3 limits the maximum hot water discharging from a bidet to 110°F (43°C). A temperature-limiting device conforming to ASSE 1070/ASME A112.1070/CSA B125.70 on the hot supply, set at rough-in, is the usual way to meet it. Do not assume a faucet limits warm water by itself. Put the limiting device on the drawings and check it at final inspection.
Pressure-test both water supply lines for leaks on capped stubs before you close the wall.
Bidet p trap and waste line
A bidet drains like a basin, not like a toilet. Wash water leaves through a waste in the bottom of the bidet, then through a trap into the drain line. There are no solids to carry, so the waste is small.
Typical waste details are below. These are not SANIKB data, so confirm them on the model spec sheet and with local code.
- Waste and trap size. A 1-1/4 in waste and bidet p trap, the same size class as a lavatory, is typical.
- Own trap. The bidet gets its own trap. Do not tie it into the toilet outlet.
- Bowl waste. Specify a pop-up or plug waste if users should be able to fill the bowl. Confirm whether it ships with the faucet or must be ordered separately.
- Venting. Vent it as you would a sink on the same branch, per local code.
For a wall hung bidet, the trap and waste usually run into the wall. That means the waste height in the wall must suit the outlet of the chosen bowl. For a back-to-wall bidet, check on the drawing whether the waste goes to the wall or the floor. In both cases, get the model drawing before you install the waste.
Bidet rough in dimensions: what the drawing gives you
Each body's dimension drawing shows hole sizes and positions. So bidet rough in dimensions start from the model drawing, with supply and drain heights set by the installer.
Here is what we read from each dimension drawing by eye. These are not stored product fields, so confirm every value on the issued drawing:
| Model | Tap hole | Waste hole | Rear fixing holes | Tap to waste / waste to front |
|---|---|---|---|---|
| LJ-D03 | Ø35 | Ø45 | Not labeled | — |
| LJ-D09 | Ø35 | Ø45 | Not labeled | — |
| LJ-D03WH | Ø35 | Ø45 | 180 mm | — |
| LJ-D09WH | Ø35 | Ø45 | 180 mm | — |
| LJ-DA15 | Ø35 | Ø45 | 180 mm | 175 / 290 mm |
| LJ-DE09 | Ø35 | Ø45 | 180 mm | 155 / 260 mm |
| LJ-DE03 | Ø40 | Ø45 | 180 mm | — |
| LJ-DE06 | Ø40 | Ø45 | 180 mm | — |
| LJ-DE08 | Ø40 | Ø45 | 180 mm | — |
| LJ-DA12 | Not labeled | Not labeled | 180 mm | 175 / 290 mm |
| FT-276 | Not labeled | Not labeled | 180 mm | — |
| FT-277 | Not labeled | Not labeled | 180 mm | — |
| LJ-DB15 | Not labeled | Not labeled | Not labeled | — |
The SANIKB bidet drawings show a Ø35 tap hole on six bodies and Ø40 on LJ-DE03, LJ-DE06 and LJ-DE08, read from the drawings. The FT-276 and FT-277 drawings show a 440 mm floor-to-rim installed height.
Use a drawing like this in three ways. Set the fixing bolt holes in the blocking or frame to the drawing spacing. Check the tap hole against the faucet shank. Then position the waste stub so the outlet lines up when you install the body.
Wall hung bidet: frame, blocking and fixing
A wall hung bidet carries no load on the floor. All of the weight, plus the user, goes into the wall. So the wall has to be built for it before you install the drywall or backer board.
Typical practice is an in-wall frame or carrier, or studs and blocking rated for the load. Confirm the method on the model spec sheet and with local code. Pick the frame on its own merits and check its fixing points against the bidet drawing.
Checks before the wall closes:
- Load rating in writing. Get the rated load of the frame or blocking from its supplier.
- Bolt spacing. Set the mounting bolts to the spacing on the bidet drawing.
- Mounting plate or rods. Confirm the frame uses a mounting plate or threaded rods that suit the bidet.
- Waste and supply positions. Install all three stubs on the frame, matched to the drawing.
- Rim height. Set the frame so the bidet rim lines up with the toilet rim beside it.
Every SANIKB body lists its installation as fixing to wall with back. A back-to-wall bidet still needs solid blocking behind the fixing points, even though the floor carries the weight.
The faucet interface: deck-mounted, single hole
A standalone bidet needs its own faucet. Unlike a bidet seat, the bowl has no built-in nozzle or controls. The faucet controls mix hot and cold water and send a warm spray from the nozzle into the bowl.
All 4 SANIKB bidet faucets are deck-mounted, single-hole faucets listed as cUPC. Each one has a short spout ending in a ball-jointed nozzle, so the user can aim the spray. Here is how they differ:
- Taper Cone Slim Lever Bidet Faucet in Chrome B099C 05: brass, chrome, slim lever on the top.
- Knurl Grip Bidet Faucet in Gun Metal Grey B703B 05: stainless steel, knurled top knob.
- Taper Cone Diamond-Knurl Bidet Faucet in Brushed Gold B099G 05: brass, diamond-knurl knob.
- Taper Cone Smooth Knob Bidet Faucet in Brushed Gold B099 05: brass, smooth knob.
B099C 05 is the only lever-handle option; the other three use a top knob. Check nozzle angle and spray on a sample before a large order.
Do not assume any faucet fits any bowl hole. Check the faucet hole on the bowl drawing against the faucet's shank, and confirm the fit in writing. The drawings show a Ø35 tap hole on some bodies and Ø40 on others (see the drawing table above), so match each faucet to each body rather than approving one faucet for the whole range. For the full range of taps, browse our bathroom faucets for wholesale and projects.
Finishes: black bidet bodies and matching the toilet
Six of the 13 bodies come in an all-black finish as well as White; FT-277 adds a two-tone option (white body, glossy black lower band). The options are:
- Wall-hung, all black: FT-276 (White / Black), LJ-D03WH and LJ-D09WH (White / Matt Black).
- Back-to-wall, all black: LJ-D03, LJ-D09 and LJ-DE08 (White / Matt Black).
- Two-tone: FT-277 (White, or Glossy Black with a white body and black lower band).
If the toilet is matt, pick a matt bidet, and ask for samples before a large order. The FT-277 wall-hung bidet pairs a white bowl with a glossy black lower band, a two-tone look rather than a black match. The LJ-D09 back-to-wall bidet in White or Matt Black suits a matt suite.
Codes differ by finish on some models. FT-276 is coded FT-276 in White and FT-276YH in Black. FT-277 is FT-277 in White and FT-277-GB in Glossy Black. Use the finish code for FT-276 and FT-277. For the LJ models, both finishes share one code, so write the finish name (White or Matt Black) on every order line.
For US and Canadian projects, the plumbing code requires a bidet body that complies with ASME A112.19.2/CSA B45.1 (UPC 410.1, IPC 408.1). Ask for that listing document for the exact model and finish code with your quotation, and confirm it before submittals. Documents for other markets (for example CE, which the factory prints against FT-276YH) are matched to the destination at quotation.
How to choose by project type
Most bidet installation decisions follow the project, not the bidet. Use these defaults, then check the bathroom against the spacing rules above.
Hotels and serviced apartments
A wall-hung pair is easier to keep clean and hygienic, since the floor under both is open. Pick one wall-hung design for every bathroom so spare parts and frames stay the same.
Multifamily and condos
Repeat one layout across units so the rough-in is identical. If the slab or wall type varies, the LJ-D03 and LJ-D09 codes are listed in both mountings. Confirm with the factory that each pair shares the same bowl before you mix them.
Residential remodels
In a remodel, a back-to-wall body avoids an in-wall carrier, but it still needs new hot and cold supplies and a new trapped, vented waste. On the SANIKB drawings the back of the body sits against the wall, so plan the waste stub in the wall behind it and confirm the outlet on the model drawing. Short bodies like LJ-DE09 or the 500 mm LJ-DE03 help in a shallow bathroom, once the mounting is confirmed in writing. If the client really wants a bidet function without new plumbing, see our guide to bidet seats and built-in bidet toilets for a one-piece toilet instead.
Common bidet plumbing mistakes to avoid
Most bidet plumbing problems are set at rough-in and found when you install the bidet. Beyond the supply, waste and spacing checks above, watch for these three:
- Unconfirmed mounting. For the seven models whose records ask for it, get the mounting confirmed in writing before you frame the wall.
- Tap hole versus faucet shank. A faucet approved on a Ø35 body may not suit the Ø40 hole on LJ-DE03, LJ-DE06 or LJ-DE08.
- Low rim next to a tall toilet. Check the 315–325 mm back-to-wall bodies against the rim of the paired toilet.
Then send a complete request. For each bidet line, list:
- Model and mounting, for example LJ-D03 back-to-wall or LJ-D03WH wall-hung.
- Size exactly as listed, such as 565 × 355 × 340 mm.
- Finish and finish code.
- Faucet model and quantity, plus the toilet you are pairing it with.
- Drawings and certification documents for your destination market.
Minimum order, samples and timing are confirmed in the written quotation per model. SANIKB replies within 12 business hours.
Ready to plan your bathrooms? Browse our standalone bidets, then send a quote request listing each model, its size and the quantity you need. We will come back with a written quotation and the drawings for every line.
Frequently asked questions
What size drain pipe for a bidet?
A bidet drain is typically a 1-1/4 in waste and trap, the same size class as a lavatory. That figure is typical, not SANIKB data: the drawings show a Ø45 waste hole in the bowl but no trap spec. Confirm the size on the model spec sheet and with local code. Give the bidet its own trap, and set the waste stub to the drawing of the exact model you order.
How far away from the toilet should a bidet be placed?
A bidet should sit at least 30 in (762 mm) center to center from the toilet. IPC 405.3.1 names the bidet directly; under UPC 402.5, confirm the toilet counts as a similar fixture. Both codes set 15 in (381 mm) to a side wall. Front clearance is 24 in (610 mm) under the UPC and 21 in (533 mm) under the IPC. Lay out both fixtures on one wall to keep the plumbing short.
How high should a bidet outlet be?
Bidet outlet height has no single standard number, so take it from the drawing of the model you order. SANIKB product fields list no supply or drain heights, but the drawings show hole positions, and FT-276 and FT-277 print a 440 mm floor-to-rim installed height. For a wall hung bidet, the installer sets the rim height on the frame. Fix that height to match the toilet first, then set the waste stub.
How do you measure a bidet before ordering?
Bidet size is measured as length × width × height, with length read as projection from the finished wall. SANIKB bodies run 485–565 mm long but only 345–365 mm wide, so projection decides the fit. Add the front clearance to the length: 24 in (610 mm) under the UPC or 21 in (533 mm) under the IPC. Then check the 15 in side spacing from the centerline and confirm the model drawing.
— Rokan, SANIKB