锥形长方形立柱盆，20英寸白色陶瓷落地式

The measurements below for the rectangular ceramic pedestal sink are taken from the factory specification drawing. Use them for rough-in planning and to confirm fit against your project drawings before placing a production order.

• Overall dimensions: 510 mm wide, 460 mm deep, 860 mm high (about 20-1/8 in wide, 18-1/8 in deep, 33-7/8 in high).
• Rectangular basin top: 510 mm by 460 mm (about 20-1/8 in by 18-1/8 in).
• Wash bowl interior, measured at the top: approximately 240 mm by 180 mm (about 9-7/16 in by 7-1/16 in).
• Bowl section depth references: 200 mm and 175 mm (about 7-7/8 in and 6-7/8 in) as shown in the front section view.
• Tap and waste: one back-center faucet hole with a single center waste outlet.

A nominal 20 by 18 by 34 in label is sometimes used in listings as a rounded shorthand, but the millimeter figures above are the controlling dimensions for specification and installation.

The basin is produced as a single glazed ceramic body. The fired glaze gives a smooth, sealed surface that is easy to wipe clean, which matters in settings where the basin sees frequent use and routine cleaning. For high-turnover environments such as hotels, apartments, and commercial restrooms, a continuous form has fewer joints than multi-part assemblies, so there are fewer points where water and grime can collect.

As a freestanding ceramic washbasin, the unit is finished on all visible faces, since the pedestal stands clear of any cabinet or wall panel. Color and finish options are set per program and confirmed when we quote.

The specification drawing shows a single faucet hole at the back center of the basin deck, suited to a single-hole mixer, with one waste outlet at the center of the bowl. Check that the faucet you plan to pair has a single-hole footprint, or ask about alternative drillings if your program runs widespread or wall-mounted taps.

Drain selection depends on whether this model includes an integral overflow. If the basin ships without an overflow, it must be paired with a non-overflow free-flow pop-up waste rather than a standard overflow pop-up, because a standard overflow drain relies on an overflow channel the basin would not have. Confirm the overflow condition for this model before the order is finalized, so the correct waste is specified for every unit.

This is a floor-standing pedestal sink, so the body rests on the finished floor and the supply and waste connections run through or behind the pedestal to the wall or floor rough-in. Because the bowl and pedestal are a single piece, there is no basin-to-column joint to seal or bracket on site.

For stability, wall fixing is recommended where the top of the basin meets the wall, with the exact fixing method confirmed in the installation guide supplied with the product. Verify your rough-in heights and supply locations against the dimensions above before the basin arrives, so plumbing is roughed in to match the single back-center tap hole and center waste.

As a wholesale pedestal basin, this model fits a range of B2B channels:

• Distributors and wholesalers stocking a freestanding basin SKU for trade and showroom customers.
• Importers and sourcing agents consolidating ceramic sanitaryware by the container.
• Private-label and own-brand bathroom brands adding a rectangular pedestal model to their range.
• Multifamily and residential developers fitting consistent units across phased construction.
• Hospitality FF&E buyers specifying guest and public washroom basins by the property.
• Kitchen and bath showrooms and dealers quoting from accurate spec and dimension files.

SANIKB supplies this product on an OEM and ODM basis. As an OEM ceramic pedestal sink, it can be produced to a buyer's branding, packaging, and program requirements, with private-label cartons and rebrandable documentation available on request. Samples can be arranged for evaluation before a production order. Minimum order quantities and lead times are confirmed with your quote.

A tall ceramic basin is fragile in transit, so protective export packaging matters for this product. For B2B orders, packaging can be built to guard the rim, bowl, and pedestal base through ocean and inland freight, with the goal of reducing breakage and damage claims on arrival. Carton specifications, packing details, and the supporting export documentation can be provided with your quotation to assist customs clearance and freight planning. Packaging can also be adapted for private-label programs that require branded outer cartons.